Iscar is announcing Penta 34 carbide inserts using a brand new PB chipformer. The PB chipformer incorporates a single cavity having a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer having a dissimilar frontal edge.

The new chipformer was fashioned for machining soft materials. It is an wonderful solution for parting bearing steel and other exceptionally ductile materials. It can be used at low feed: 0.03 to 0.10 mm/rev.

The combination of the brand new chipformer and IC908 grade provides remarkable chip breaking and tool life results. The Penta 34-PB is available in a 1.5 to 3.0 mm width range, made from the ingenuous IC908 PVD coated grade. The unique family advances the application range of Iscar's most economical grooving and parting PENTA 34 carbide inserts. The Penta 34-PB, when stacked up against to a competitor's cutter, is a triumphant solution for machining any soft and ductile material.

Iscar's Upgrades for Parting

Iscar has developed a brand new family of reinforced Tang-Grip blades for the applauded TRAUB (TNL and TNK models) and INDEX (MS18C model) turn/mill machines. These blades, due to their reinforced configuration, can be implemented in long overhang. Only the part of the blade required for penetration (cutting depth) has a reduced width. The rest is thick, which provides enhanced rigidity and stiffness. These blades are an outstanding solution for parting and grooving between the main and sub-spindle of turn/mill machines. The single-ended insert has a incredibly rigid clamping and therefore provides a substantially important advantage over any other system.

Further additions to Iscar's Grip family are Do-Grip carbide inserts formed from the cutting edge Sumo Tec carbide grades: IC807 IC808 and IC830. The brand new Sumo Tec grades significantly lengthen insert life, due to the utmost advanced coating technology followed by a specific surface treatment. This also provides enhanced tool life due to lesser surface stress and an evenly coated top surface. The flat surface contributes to constant uninterrupted chip flow, less generated heat and less friction. The new process improves toughness and chipping resistance and thus diminishes friction and built-up edge. This in turn optimizes and prolongs tool life at elevated machining conditions for all types of work piece materials. The new PVD process is composed of Iscar's AL-TEC coating technology, utilizing the unique surface treatment.

Iscar's Chip Splitting Inserts
Iscar's completely new HM90 APCR 220605-CS grooved carbide inserts put an end to chip obstruction dilemmas in rough milling of aluminum, where chips can pile up. They are a part of Iscar's growing Helialu HM90 line of inserts tailored specifically for aluminum milling. With 2 grooves pressed into every single polished cutting face, the inserts split aluminum chips into a easy size for easy, reliable evacuation despite the application's characteristic elevated chip volume. The 22 mm inserts, each with two edges, are designed to magnify metal removal over the profuse range of aluminum roughing conditions, from high power/low speed to high power/high speed. They work especially well with Iscar's new HM90 EAL/FAL...22 aluminum rough milling cutters. Besides dependably clearing chips, the inserts conserve power and trim down chatter in long-overhang setups. The inserts feature a cavity on the bottom to be sure correct mounting in cutter chip pockets equipped with standard spring pins. For best chip control, Iscar proposes using the HM90 APCR chip-splitting insert only in cutters with an even number of flutes.

A Couple Of The Several Improvements In Carbide Inserts Coming From Iscar Over The Years
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.

New End Mills Coming From Iscar Can Enhance Productivity While Reducing Costs
Manufacturers and die & mold shops can banish chatter problems in numerous milling operations with Iscar's new Chatterfree end mills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the primary source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.

Iscar Offers A Revolutionary Line Of Slitting Cutters Using Tang-Grip Technology And The Durability Of Sumo Tec Grades
Iscar now offers a family of high-performance slitting tools that combine the convenience and security of Tang-Grip clamping with the added durability of the new Sumo Tec insert grades. The concept, already proven successful in Tang-Grip parting tools, has now been extended to slitting cutters.

Iscar Recently Releases Numerous New Lines To Continue Their Family Of Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.

Several Advancements Have Multiplied Iscar's Families Of Indexable Endmills For Elevated Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.

A Number Of Improvements In Carbide Inserts Provided By Iscar Over The Last Decade
Iscar is announcing a brand new unique milling system that includes tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has meaningful advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, decreased cutting forces resulting in better performance.

Modern Car Manufacturing Jobs To Help Save The Economic State
The global recession the economy is experiencing in the past few years have pushed major companies to close down and stop their operations.

Acquiring An Automotive Engineering Job Today.
Automotive engineers who have years of experience in the automotive industry have the ability and skills of overseeing new projects and product development.

Look Out For Automotive Manufacturing Jobs.
There is no point in denying that workers serving in the automotive industry are also suffering from the economic recession that everybody is experiencing world wide.